Direct Answer
AnyLeak provides leak and moisture detection services in British Columbia using non-invasive methods — acoustic correlation, tracer gas, thermal imaging, and moisture metering — to find leaks without digging or damage. Every inspection includes a written, insurance-ready report. Call (604) 269-5325 for a free phone consult.
🔄 Reviewed and maintained by the AnyLeak team — October 2026. Rated 5 stars by BC customers.
Cost of Utility Locating in BC
Honest cost guide for utility locating across BC — pricing, what affects cost, budgeting.
Insurance-Friendly ReportsServing All of BC
Cost of Utility Locating in BC
This guide answers “cost of utility locating in bc” honestly, from the perspective of a senior BC utility locator with over two decades of field experience. The goal is to give you the same understanding that drives our daily practice — what works, what doesn’t, and when to call for help.
Below: the practical context for BC, the standard answer, the edge cases that matter, and our service recommendation. Most pages also include the relevant regulatory or industry-standards references (WorkSafeBC, BC One Call, ASCE 38, BC Building Code where applicable).
Need to talk it through? Call us — most utility-locating decisions can be made in a 5-minute conversation with a senior technician.
Key points at a glance
- Practitioner-honest answer based on BC field experience
- Regulatory and standards references included
- Decision-grade content for project teams
- Cross-references to detailed service pages
- Updated for 2026 BC utility locating practice
- From senior technicians at AnyLeak since 1999
What We Detect Inside the Concrete
Concrete is rarely “just concrete.” Modern slabs in BC carry a tight grid of structural steel, electrical conduits, water lines, low-voltage cabling, and — in post-tensioned construction — high-tension cables that will fail catastrophically if cut. Our scans map every embedded element before any drilling, coring, or cutting begins.
Reinforcing Steel (Rebar)
#3 through #11 bars mapped by size, depth, and spacing. We mark the actual rebar positions on the surface so your crew can drill between bars, not through them.
Post-Tension Cables
Stressed PT tendons (often 270 ksi) are located and clearly flagged. Cutting one causes a violent recoil that can destroy a slab section and seriously injure workers — never drill blind in a PT slab.
Electrical & Low-Voltage Conduit
EMT, rigid, and PVC conduits up to 4″ trace routing across the slab. We identify branch lines, expansion fittings, and pull-box locations.
Domestic & Hydronic Water Lines
Copper, PEX, and embedded radiant-heating loops located non-destructively. We can also pressure-trace any line you suspect is leaking.
Voids, Honeycomb & Delamination
Hidden voids under the slab, honeycombing inside the pour, and delamination layers detected with GPR + impact-echo cross-check.
Slab Thickness & Cover
Verify slab thickness from one side, measure rebar cover for code compliance, and confirm pour quality before structural sign-off.
Common Scenarios We Solve On This Page
Decision context
Use this when deciding how to approach a utility-locating need.
Scope discussion
Use this in scope conversations with stakeholders.
Educational reference
Use this as educational reference for project teams.
Permit and insurance context
Use this to understand permit and insurance implications.
Cost and timeline planning
Use this for planning cost and timeline expectations.
Who Books This Type of Scan
Project managers and superintendents use this for scope and risk planning.
Property owners read this to understand the practical context.
Engineering and design consultants reference this for client briefings.
Educational use for industry professionals and trades.
Our Concrete Scanning Process — Step by Step
1. Pre-scan briefing
Before we step on site we want your drawings, photos, the exact intent (“I need to core eight 4″ holes through this 8″ suspended slab”), and any constraints — live wiring, occupied tenant space, sensitive equipment below. A 5-minute call almost always saves a costly surprise.
2. Site walk & grid layout
On arrival the technician confirms safe access, marks a working grid (typical 1×1 m or 1×1 ft), and photographs baseline conditions. If the slab is dirty or coated we sweep and may light-sand to ensure good antenna contact.
3. GPR scanning passes
We run an orthogonal grid with our 1600/2000 MHz concrete antenna — one set of lines in the X-direction, one in the Y. The real-time image is reviewed on screen; hits are paint-marked on the slab directly as the survey progresses.
4. Verification & cross-check
For high-stakes work (PT slabs, deep cores, occupied buildings below) we cross-verify with a secondary method — electromagnetic locator, half-cell, or impact-echo — to remove false positives and pin down depths.
5. Marking, photos & report
Every embedded element gets a colour-coded mark on the slab (red = PT, blue = rebar, green = conduit, yellow = water/hydronic). Before we leave you receive on-site photos and, on the next 1-2 business days, a stamped PDF report with annotated drawings.
6. Standby for drilling/coring
For complex jobs we stay on site while your contractor drills the first 1-2 holes, so any unexpected reading can be addressed in real time. Once we’re confident, we hand off and you continue safely.
Equipment We Bring on a Concrete Scan
| Instrument | What It Sees | When We Use It |
|---|---|---|
| GSSI StructureScan Mini XT / Proceq GP8000 | Rebar, PT cables, conduits to ~18″ depth; voids; slab thickness | Default tool on every scan |
| 1600 MHz & 2600 MHz antennas | High-resolution imaging of upper 8″ of slab | Shallow drilling, tile/topping work |
| Electromagnetic locator (Hilti PS 1000-style) | Confirms ferrous rebar & conductive conduit | Cross-check on critical hits |
| Cover meter (Proceq Profometer) | Precise rebar diameter & cover depth | Code-compliance reports |
| FLIR T-series thermal | Hydronic loops, hot/cold lines, moisture | Radiant-heat slabs, suspected leaks |
| Impact-echo / ultrasonic (Olson, Pundit) | Voids, delamination, slab thickness from one side | Structural assessments |
| Acoustic correlator & pressure rig | Active water-line leak location through slab | Concrete-encased leak hunts |
Every instrument is calibrated and traceable. Calibration certificates can be supplied with the report on request — useful for tenders, insurance claims, and government work.
What Does a Concrete Slab Scan Cost in BC?
Concrete scanning is priced by the technician’s time and the scope of marking required. As a guide for budgeting:
- Small single-area scan (one room, 1-2 cores) — typically a half-day rate, suitable for residential or single-suite work.
- Medium scope (full floor plate, multiple drill zones) — full-day rate; includes orthogonal grid, marking, and PDF report.
- Multi-floor or PT slab survey — quoted by floor area; PT slabs require additional verification time.
- Stand-by during drilling — hourly add-on; recommended for any post-tension or occupied-suite work below.
- After-hours / weekend work — premium quoted upfront; common for retail and hospital scans where daytime access isn’t possible.
Every quote is itemised and emailed before we mobilise. There are no junk fees, no minimum subscriptions, and no surprise add-ons. Get an honest number at (604) 269-5325.
BC Building Code & Worksite-Safety Context
WorkSafeBC and the BC Building Code don’t mandate a concrete scan by name — but they do mandate that you not cut, drill, or core into a structural slab without first verifying what’s inside. Scanning is the standard of care, and any competent general contractor or strata council will expect to see scan documentation before drilling proceeds.
For post-tensioned slabs the bar is higher still: cutting a PT cable is treated as a near-miss safety incident even when no one is injured. Most municipalities (City of Vancouver, City of Burnaby, City of Surrey, District of West Vancouver, City of Victoria) will ask to see a scan report as part of any tenant-improvement permit involving slab penetrations.
Our reports include the technician’s name, scan date, equipment used, slab area covered, and a marked drawing. That documentation is enough for almost every permit, insurance, and warranty conversation in BC.
Service Areas Across British Columbia
We mobilise to Vancouver, Burnaby, Surrey, Richmond, Coquitlam, North Vancouver, West Vancouver, Delta, Langley, Maple Ridge, New Westminster, Port Coquitlam, Port Moody, White Rock, Abbotsford, Chilliwack, Mission, Squamish, Whistler, Victoria, Nanaimo, Kelowna, Kamloops, Prince George, and most BC communities in between. For a full list see our service areas hub.
Outside the Lower Mainland we typically batch concrete-scan work with other inspections to keep mobilisation fair. Call (604) 269-5325 with your address and timeline and we’ll quote travel honestly.
Why BC Property Owners Choose AnyLeak for Concrete Scanning
- Since 1999 — over two decades of BC concrete work, from heritage West-End buildings to modern high-rises in Yaletown and Burnaby.
- One responsible technician per job — no junior left alone with your slab. Senior leads run every PT and high-risk scan personally.
- Written, stamped reports — every scan ends with annotated drawings, photos, and notes your contractor, architect, or insurer can act on.
- Insurance-friendly documentation — adjusters across BC accept our reports as expert evidence for water-loss, structural, and pre-renovation claims.
- BC-wide coverage — Vancouver, Fraser Valley, Sea-to-Sky, Vancouver Island, Okanagan, Kootenays, and Northern BC. Travel charges are quoted upfront, never hidden.
- Standby during drilling — for high-risk cores we stay on site through the first holes so any anomaly can be re-scanned on the spot.
Frequently Asked Questions
How accurate is your utility locating?
Active EM locating typically achieves horizontal accuracy of ±10% of depth (e.g., ±5 inches on a 4-foot-deep line). GPR can achieve tighter accuracy in good ground conditions. Quality Level A (vacuum-excavation verification) is the only way to get exact positional certainty — we coordinate with hydrovac contractors when QL-A is required by the scope.
Can you locate every utility on my site?
We locate all conductive utilities (metallic gas, water, electrical, telecom, CCTV, cathodic protection) and most non-conductive utilities with GPR (PVC water, fibre optic in conduit, plastic gas). Direct-bury fibre with no tracer wire and abandoned utilities without records are the most challenging — we flag those limits in writing on every locate.
Do I still need to call BC One Call?
Yes — BC One Call (1-800-474-6886) handles public utility locates (BC Hydro, FortisBC, Telus, Shaw) for free and is mandatory before any excavation in BC. Our private locating service covers everything BC One Call doesn’t — private utilities, site lines, abandoned utilities, and utilities the public locator misses.
What deliverables come with a locate?
On-site spray paint markings using APWA colour code, optional pin flags for outdoor work, photos of all markings on the day of the locate, and a stamped PDF report on the next 1-2 business days that includes a site sketch, utility types found, depth estimates, and limits of the survey.
How deep can you locate utilities?
Active EM locating routinely reaches 8-15 feet for most conductive utilities. GPR depth depends entirely on soil conductivity — typically 3-8 feet in BC soils, up to 15 feet in dry sandy ground. Very deep utilities (>15 ft) may require specialised low-frequency GPR or vacuum-excavation verification at suspected depths.
Can you do a locate during winter or wet weather?
Yes — EM locating is unaffected by weather. GPR works in wet ground but signal attenuation is higher, reducing maximum depth. We schedule locates year-round across BC; winter and shoulder-season are often quieter scheduling windows.
Talk to a Senior Locator
Speak with a senior technician about your concrete-scan requirements. We provide upfront quotes, written scope, photo/PDF deliverables, and reports your contractor, architect, or insurer can act on.
Written reportsInsurance accepted
A Closer Look at This Service
Hidden water is the most common source of expensive damage in British Columbia homes and buildings. It works silently for weeks or months, and by the time it becomes visible, the repair bill is measured in thousands rather than hundreds.
The best detection work is done by people who have seen the region’s buildings and buried systems fail in every common way. That experience is what turns a set of readings into a confident, cross-verified answer.
The investigation is a quiet, methodical process. Instruments are calibrated on site, readings are recorded, and the technician explains what each step is looking for. There is no demolition, no noise beyond the instruments, and no mess left behind.
How the Investigation Is Delivered
Every investigation follows the same disciplined sequence: consultation, survey, testing, cross-verification, marking, and documentation. The sequence is deliberate, and each step builds on the last.
- Step 1: Consultation to understand the situation and the history
- Step 2: Site survey and indicator mapping
- Step 3: Testing of the suspected systems with matched methods
- Step 4: Cross-verification of the finding
- Step 5: Marking and documentation
- Step 6: Written, dated report
A fourth mistake is hiring a repair contractor to find the leak. Contractors are paid to repair, and their interest is in the work, not in the precision of the location. An independent detection team has no repair to sell, only an answer to deliver.
What This Costs
Most property-level investigations in British Columbia are quoted as a fixed fee once the situation is understood. The quote covers the technician’s time, the instruments, the investigation, and the written report.
Every property is different, which is why pricing follows the investigation plan rather than a menu. The free consultation defines the scope, and the fixed quote follows it. What you are quoted is what you pay.
Insurance and Documentation
For BC policyholders, the practical value is speed: the claim starts with the report already in hand, instead of weeks of back-and-forth while the insurer tries to establish what happened.
The report also protects the policyholder. When the cause is documented at the time of the loss, there is no later dispute about what was found, when it was found, or what the condition was.
What the Report Includes
The report is written in plain language first and professional language second. Owners read the conclusion and the cause; contractors and adjusters read the method notes and the readings. Both are in the same document.
You keep the report. It documents the finding, the condition at the time of the investigation, and the guidance for the repair, which is useful for warranty, insurance, and future reference.
When to Call
Call when a decision needs documentation: an insurance claim, a real estate transaction, a strata dispute, or a warranty process. Those decisions run on evidence, and the evidence has to exist before the deadline.
Call when a decision needs documentation: an insurance claim, a real estate transaction, a strata dispute, or a warranty process. Those decisions run on evidence, and the evidence has to exist before the deadline.
How to Prepare the Property
If there is an active leak, the priority is containment: shut off the water at the fixture or main if it can be done safely, move valuables away, and photograph the scene. The technician can be guided by phone while en route.
If there is an active leak, the priority is containment: shut off the water at the fixture or main if it can be done safely, move valuables away, and photograph the scene. The technician can be guided by phone while en route.
Common Questions
Is this service non-invasive?
Yes. Every method used works from the surface and leaves no marks. Nothing is cut, dug, or permanently marked during the investigation.
How accurate is the location?
With cross-verified methods, locations are typically within a metre or less, and slab locations within inches.
Is the report useful for insurance?
Yes. The report documents the cause, the extent, the methods used, and the readings, structured for claims and engineering review.
How long does an investigation take?
Most property-level investigations complete within a day, and the written report follows within one to two business days.
Do you repair leaks?
No. Detection and documentation are the service. The report guides the repair contractor to the exact location.
What does this cost?
The quote is fixed before work begins, based on the scope defined in the free consultation. What you are quoted is what you pay.
Call (604) 269-5325 or email info@anyleak.ca for a free consultation. The report is dated, documented, and written to the standard insurers and engineers expect.
★★★★★
"I recently hired AnyLeak for leak repairs on my roof and deck canopy, and I couldn't be happier with the results."
Trevor Houston
Google Review
Pricing & Free Phone Consult
AnyLeak provides clear pricing before any work begins — no surprises when the inspection is complete. Costs depend on property size, the systems involved, and the methods required.
- Free phone consultation to discuss your situation and estimate scope
- Written quote provided before the inspection starts
- Many insurance policies cover the cost of finding a hidden leak — your dated written report supports the claim
- Detection is separate from repair; you choose the contractor for repairs with full information