Direct Answer
AnyLeak provides condo leak inspection services in British Columbia using non-invasive methods — acoustic correlation, tracer gas, thermal imaging, and moisture metering — to find leaks without digging or damage. Every inspection includes a written, insurance-ready report. Call (604) 269-5325 for a free phone consult.
🔄 Reviewed and maintained by the AnyLeak team — October 2026. Rated 5 stars by BC customers.
Finding the leak is half the job; the other half is knowing how far the water went. Moisture mapping measures that — suite by suite, surface by surface — with calibrated meters and thermal imaging, producing a documented extent map. In a condo, that map decides drying scope, which units are affected, and what the insurer accepts. AnyLeak.ca has mapped water through BC multi-unit buildings since 1999.
When mapping matters most
- After a located leak — defining the wet zone before drying or repair; see the process.
- After a flood event — confirming which suites and assemblies took water.
- Verifying dry-out — proving a past loss was actually dried, not just patched; see musty smell investigations.
- Distinguishing legacy damp from new leaks in remediated-era buildings.
Measured, not guessed
Readings are taken on a grid with pin and pinless meters, referenced against dry standards for the same material, and overlaid with thermal imagery. The deliverable is a marked plan: wet, borderline, dry. Restoration contractors scope from it; adjusters rely on it — see insurance documentation.
FAQ
The surface feels dry — can the assembly still be wet? Very commonly yes: drywall surfaces dry first while cavities and slabs hold water for weeks.
Can you map without removing finishes? Yes — mapping is non-destructive; openings only follow confirmed findings.
Need the extent in writing? Call (604) 269-5325 or request an assessment.
A Closer Look at This Service
Hidden water is the most common source of expensive damage in British Columbia homes and buildings. It works silently for weeks or months, and by the time it becomes visible, the repair bill is measured in thousands rather than hundreds.
The best detection work is done by people who have seen the region’s buildings and buried systems fail in every common way. That experience is what turns a set of readings into a confident, cross-verified answer.
The investigation is a quiet, methodical process. Instruments are calibrated on site, readings are recorded, and the technician explains what each step is looking for. There is no demolition, no noise beyond the instruments, and no mess left behind.
How the Investigation Is Delivered
Every investigation follows the same disciplined sequence: consultation, survey, testing, cross-verification, marking, and documentation. The sequence is deliberate, and each step builds on the last.
- Step 1: Consultation to understand the situation and the history
- Step 2: Site survey and indicator mapping
- Step 3: Testing of the suspected systems with matched methods
- Step 4: Cross-verification of the finding
- Step 5: Marking and documentation
- Step 6: Written, dated report
A fourth mistake is hiring a repair contractor to find the leak. Contractors are paid to repair, and their interest is in the work, not in the precision of the location. An independent detection team has no repair to sell, only an answer to deliver.
What This Costs
Every property is different, which is why pricing follows the investigation plan rather than a menu. The free consultation defines the scope, and the fixed quote follows it. What you are quoted is what you pay.
Most property-level investigations in British Columbia are quoted as a fixed fee once the situation is understood. The quote covers the technician’s time, the instruments, the investigation, and the written report.
Insurance and Documentation
The report produced after a this investigation investigation is written with insurers in mind. It documents the cause, the extent, the methods used, and the readings taken, so the adjuster has everything needed to process the claim.
The report produced after a this investigation investigation is written with insurers in mind. It documents the cause, the extent, the methods used, and the readings taken, so the adjuster has everything needed to process the claim.
What the Report Includes
The report is written in plain language first and professional language second. Owners read the conclusion and the cause; contractors and adjusters read the method notes and the readings. Both are in the same document.
The written report is the deliverable that separates professional detection from a good guess. It includes the confirmed location, the depth where applicable, the readings, the photographs, the methods used, and an interpretation of the cause and contributing factors.
When to Call
Call when a decision needs documentation: an insurance claim, a real estate transaction, a strata dispute, or a warranty process. Those decisions run on evidence, and the evidence has to exist before the deadline.
Call when a repair contractor cannot find the source. Blind replacement of pipe, membrane, or roofing is expensive, and it fails when the true cause is elsewhere. The investigation answers the question the contractor could not.
How to Prepare the Property
Nothing else needs to be done. The investigation does not require demolition, preparation of the systems, or any work on your part beyond access. Showing up with the history is the whole preparation.
If there is an active leak, the priority is containment: shut off the water at the fixture or main if it can be done safely, move valuables away, and photograph the scene. The technician can be guided by phone while en route.
Common Questions
Is this service non-invasive?
Yes. Every method used works from the surface and leaves no marks. Nothing is cut, dug, or permanently marked during the investigation.
How accurate is the location?
With cross-verified methods, locations are typically within a metre or less, and slab locations within inches.
Is the report useful for insurance?
Yes. The report documents the cause, the extent, the methods used, and the readings, structured for claims and engineering review.
How long does an investigation take?
Most property-level investigations complete within a day, and the written report follows within one to two business days.
Do you repair leaks?
No. Detection and documentation are the service. The report guides the repair contractor to the exact location.
What does this cost?
The quote is fixed before work begins, based on the scope defined in the free consultation. What you are quoted is what you pay.
Call (604) 269-5325 or email info@anyleak.ca for a free consultation. The report is dated, documented, and written to the standard insurers and engineers expect.
★★★★★
"We had a roof leak at our warehouse and they were great to work with. They came out quickly and found the problem."
Christo Sypsas
Google Review