Direct Answer
AnyLeak provides leak and moisture detection services in British Columbia using non-invasive methods — acoustic correlation, tracer gas, thermal imaging, and moisture metering — to find leaks without digging or damage. Every inspection includes a written, insurance-ready report. Call (604) 269-5325 for a free phone consult.
🔄 Reviewed and maintained by the AnyLeak team — October 2026. Rated 5 stars by BC customers.
A solar array fails quietly: one hot cell, one dead string, one failed diode at a time — each invisible from the ground and each subtracting from production every sunny day. Aerial radiometric thermography reads the whole array’s temperature signature in one flight, while it generates. AnyLeak.ca inspects solar farms and commercial rooftop PV across BC, extending the same drone thermal practice we built finding water.
What the thermal camera finds
- Hot spots and defective cells — point overheating that degrades modules and, left long enough, becomes a fire risk
- String failures and bypass-diode faults — their thermal patterns are distinct and readable from the air
- Underperforming modules — radiometric temperature comparison across the array flags the laggards
- Soiling, shading and connection issues — separated from genuine module faults so O&M effort lands in the right place
How an inspection runs
Flights run in generation conditions (the faults show under load), with a radiometric 640×512-class sensor, thermal sensitivity (NETD) of roughly 50 mK or better, and visual-plus-thermal overlay. Every anomaly is GPS-tagged to module level, so the report reads as a punch list your O&M team can walk to — no shutdown, no panel-by-panel handheld survey.
Who uses it in BC
- Solar farm owners and operators — commissioning baselines, warranty claims, annual O&M scans
- Commercial rooftop PV owners — arrays above warehouses and plants, inspected with the roof itself (see roof thermal work)
- Institutions and public facilities — performance verification on public-money systems
FAQ
Does the system shut down for inspection? No — the opposite: the array must be producing for the thermal signatures to show.
Can you tell a dirty panel from a broken one? Usually yes — soiling, shading and electrical faults have distinct thermal patterns; the report separates “clean it” from “replace it.”
Array under-producing? Call (604) 269-5325 or request an assessment — part of the aerial inspection practice.
A Closer Look at This Service
The cost of finding a leak is small compared to the cost of the damage it causes. A month of undetected leaking can wet insulation, rot framing, wash soil, and attract mould in the time it takes to book an inspection.
Local knowledge matters because the same symptom can point to completely different causes in different cities. The interview, the property history, and the site conditions are always weighed together before any instrument is deployed.
You do not need to prepare anything except access to the relevant areas. The technician will ask where the indicators are, which systems have been worked on, and what the history shows, and the answers shape the plan.
How the Investigation Is Delivered
Every investigation follows the same disciplined sequence: consultation, survey, testing, cross-verification, marking, and documentation. The sequence is deliberate, and each step builds on the last.
- Step 1: Consultation to understand the situation and the history
- Step 2: Site survey and indicator mapping
- Step 3: Testing of the suspected systems with matched methods
- Step 4: Cross-verification of the finding
- Step 5: Marking and documentation
- Step 6: Written, dated report
A fourth mistake is hiring a repair contractor to find the leak. Contractors are paid to repair, and their interest is in the work, not in the precision of the location. An independent detection team has no repair to sell, only an answer to deliver.
What This Costs
Most property-level investigations in British Columbia are quoted as a fixed fee once the situation is understood. The quote covers the technician’s time, the instruments, the investigation, and the written report.
The comparison that matters is not detection cost versus no cost; it is detection cost versus the cost of an undetected leak. One targeted repair, guided by an exact location, almost always costs less than exploratory work and repeated damage.
Insurance and Documentation
The report produced after a this investigation investigation is written with insurers in mind. It documents the cause, the extent, the methods used, and the readings taken, so the adjuster has everything needed to process the claim.
Insurance claims fail most often because of missing documentation. A dated, photographed, method-by-method report removes that failure point and gives the adjuster a professional document they can rely on.
What the Report Includes
You keep the report. It documents the finding, the condition at the time of the investigation, and the guidance for the repair, which is useful for warranty, insurance, and future reference.
The report is written in plain language first and professional language second. Owners read the conclusion and the cause; contractors and adjusters read the method notes and the readings. Both are in the same document.
When to Call
Call before the damage becomes visible if the meter is moving with everything off. That reading is the earliest and cheapest moment to act, and acting early is what makes the repair small.
Call when a decision needs documentation: an insurance claim, a real estate transaction, a strata dispute, or a warranty process. Those decisions run on evidence, and the evidence has to exist before the deadline.
How to Prepare the Property
If there is an active leak, the priority is containment: shut off the water at the fixture or main if it can be done safely, move valuables away, and photograph the scene. The technician can be guided by phone while en route.
Clear access to the meter, the main shut-off, the water heater, and the areas showing indicators speeds the investigation. A cleared path saves the technician’s time, which is your time on the quote.
Common Questions
Is this service non-invasive?
Yes. Every method used works from the surface and leaves no marks. Nothing is cut, dug, or permanently marked during the investigation.
How accurate is the location?
With cross-verified methods, locations are typically within a metre or less, and slab locations within inches.
Is the report useful for insurance?
Yes. The report documents the cause, the extent, the methods used, and the readings, structured for claims and engineering review.
How long does an investigation take?
Most property-level investigations complete within a day, and the written report follows within one to two business days.
Do you repair leaks?
No. Detection and documentation are the service. The report guides the repair contractor to the exact location.
What does this cost?
The quote is fixed before work begins, based on the scope defined in the free consultation. What you are quoted is what you pay.
Call (604) 269-5325 or email info@anyleak.ca for a free consultation. The report is dated, documented, and written to the standard insurers and engineers expect.
★★★★★
"Our flat roof developed a leak, and Anyleak responded quickly. They completed a temporary repair right away."
Sorin Silivestru
Google Review