Direct Answer
AnyLeak provides leak and moisture detection services in British Columbia using non-invasive methods — acoustic correlation, tracer gas, thermal imaging, and moisture metering — to find leaks without digging or damage. Every inspection includes a written, insurance-ready report. Call (604) 269-5325 for a free phone consult.
🔄 Reviewed and maintained by the AnyLeak team — October 2026. Rated 5 stars by BC customers.
A district metered area turns a water system into something measurable: one zone, one meter, and a minimum night flow that tells you — every single night — whether the zone is leaking. When that number steps up and stays up, somewhere in the zone a pipe has opened. Finding it inside the maze of mains and services is the investigation. AnyLeak.ca chases DMA anomalies to located leaks for BC utilities. Since 1999.
The DMA investigation sequence
- Confirm the signal — night-flow trend against seasonal baseline; a step change is a leak, a ramp is often several.
- Step test — with your operators valving, the zone closes down section by section while the meter watches; the section that drops the flow carries the leak.
- Log the section — overnight noise loggers narrow it to spans between fittings.
- Pinpoint — correlation and ground microphone mark the dig point.
- Verify — post-repair night flow returns to baseline, documented.
No DMAs yet? Still workable
Plenty of BC systems aren’t zoned. Temporary zone isolation with existing valves plus portable metering achieves a rough step-test capability, and systematic acoustic surveying covers the rest — the leaks don’t care whether the zone is permanent. Where districts are considering DMA build-out, located-leak results make the business case concrete; see NRW reduction.
FAQ
Night flow rose but no leak surfaces anywhere — typical? Completely: zone leaks commonly drain to storm sewers, ditches or permeable ground and never show. The meter sees what the surface hides.
Who operates valves during step tests? Your crews, always — we instrument, sequence and interpret; the system stays in your operators’ hands.
Part of municipal water main leak detection. Zone misbehaving? Call (604) 269-5325 or request an investigation.
A Closer Look at This Service
The most expensive leak is the one that was never located. Exploratory openings, repeated drywall repairs, and months of a running meter all cost more than a single professional investigation with an exact answer.
Local knowledge matters because the same symptom can point to completely different causes in different cities. The interview, the property history, and the site conditions are always weighed together before any instrument is deployed.
You do not need to prepare anything except access to the relevant areas. The technician will ask where the indicators are, which systems have been worked on, and what the history shows, and the answers shape the plan.
How the Investigation Is Delivered
Every investigation follows the same disciplined sequence: consultation, survey, testing, cross-verification, marking, and documentation. The sequence is deliberate, and each step builds on the last.
- Step 1: Consultation to understand the situation and the history
- Step 2: Site survey and indicator mapping
- Step 3: Testing of the suspected systems with matched methods
- Step 4: Cross-verification of the finding
- Step 5: Marking and documentation
- Step 6: Written, dated report
A fourth mistake is hiring a repair contractor to find the leak. Contractors are paid to repair, and their interest is in the work, not in the precision of the location. An independent detection team has no repair to sell, only an answer to deliver.
What This Costs
Most property-level investigations in British Columbia are quoted as a fixed fee once the situation is understood. The quote covers the technician’s time, the instruments, the investigation, and the written report.
Every property is different, which is why pricing follows the investigation plan rather than a menu. The free consultation defines the scope, and the fixed quote follows it. What you are quoted is what you pay.
Insurance and Documentation
Insurance claims fail most often because of missing documentation. A dated, photographed, method-by-method report removes that failure point and gives the adjuster a professional document they can rely on.
The report also protects the policyholder. When the cause is documented at the time of the loss, there is no later dispute about what was found, when it was found, or what the condition was.
What the Report Includes
The report is written in plain language first and professional language second. Owners read the conclusion and the cause; contractors and adjusters read the method notes and the readings. Both are in the same document.
Reports are dated and structured so that any licensed contractor can take the marked location and proceed directly to the repair. They are also accepted by insurers, engineers, property managers, and, when needed, in dispute processes.
When to Call
Call when a decision needs documentation: an insurance claim, a real estate transaction, a strata dispute, or a warranty process. Those decisions run on evidence, and the evidence has to exist before the deadline.
Call when the indicator is persistent, when it repeats after a repair, or when it is accompanied by a second indicator. A single passing event can be a coincidence; a pattern is a leak.
How to Prepare the Property
Nothing else needs to be done. The investigation does not require demolition, preparation of the systems, or any work on your part beyond access. Showing up with the history is the whole preparation.
The best preparation is information: when the issue started, what changed around that time, what the weather did, and what has already been tried. That history is often more valuable than any instrument.
Common Questions
Is this service non-invasive?
Yes. Every method used works from the surface and leaves no marks. Nothing is cut, dug, or permanently marked during the investigation.
How accurate is the location?
With cross-verified methods, locations are typically within a metre or less, and slab locations within inches.
Is the report useful for insurance?
Yes. The report documents the cause, the extent, the methods used, and the readings, structured for claims and engineering review.
How long does an investigation take?
Most property-level investigations complete within a day, and the written report follows within one to two business days.
Do you repair leaks?
No. Detection and documentation are the service. The report guides the repair contractor to the exact location.
What does this cost?
The quote is fixed before work begins, based on the scope defined in the free consultation. What you are quoted is what you pay.
Call (604) 269-5325 or email info@anyleak.ca for a free consultation. The report is dated, documented, and written to the standard insurers and engineers expect.
★★★★★
"They fixed my leaking roof in just 1 hour. The guys came to my home the prompt and did a great job."
Anmol Brar
Google Review